Search the Community
Showing results for tags 'samwiseg0'.
Found 8 results
-
Version 2022.03.16
491 downloads
LRS Screw Terminal Cover Designed to cover the screw terminals for several LRS style PSUs. Other Meanwell PSU may work. Feel free to ping me in discord to add to the compatibility list below. Pro tip: These are very snug to the point it will bow. This is intentional as it was designed to take some effort to take off. Printing Default voron settings No supports needed Compatibility List LRS-50 LRS-200 -
Version 2022.03.16
132 downloads
Voron 2.4 AB Plug (Microfit 1x4) This mod is to add a plug to the gantry to connect the A -
Version 2022.02.13
18 downloads
ESP8266 NodeMCU Din Mount Designed to hold an ESP8266 NodeMCU. ESPs are commonly used to control LEDs using the WLED project. The ESP can be mounted in either direction. The model included can be mounted to the original 2.4 din clip or the newer Trident din clip. Printing Default voron settings No supports needed BOM Size Qty M3x8 4 M2x10 2 Trident PCB Din Clip 1 -
Version 2022.02.17
16 downloads
4 Channel Relay Under Deck Mount Mod to mount a 4 channel GPIO controlled relay in the electronics compartment. Printing Default voron settings No supports needed BOM Size Qty 4 Channel relay 1 M3x8 or M3x6 4 M5x8 2 M5 T-Nut 2 -
Version 2022.02.02
0 downloads
Corsair Flash Voyager GTX Din Mount Din carrier for a Corsair Flash Voyager GTX. To be able to plug in the USB drive you can purchase a small USB extension cable located in the BOM below. The model included can be mounted to the original 2.4 din clip or the newer Trident din clip. Printing Default voron settings No supports needed BOM Size Qty M2x10 2 Trident PCB Din Clip 1 Corsair Flash Voyager GTX 1 .5ft USB extension (Optional) 1 -
Version 2022.02.02
363 downloads
Extrusion/Chamber Thermistor Mount Designed to mount a NTC100K Thermistor Sensor to 2020 extrusions. Printing Default voron settings No supports needed BOM Size Qty NTC100K Thermistor 1 M3x8 1 M3 T-Nut 1 -
Version 2022.02.01
257 downloads
Microfit 2x3 Skirt Connector (ADXL) Mod for a Microfit 2x3 connector to be mounted in the bestagons. Typically used for ADXL but can be used as a general connector for anything outside the printer. Pro tip: I found that adding some hot-glue while installing it into the skirt makes it a bit more robust for unplugging and plugging in. This is originally based off of this mod. It was modified to not require supports and have a bit tighter fit onto the connector. Printing Default voron settings No supports needed BOM Size Qty Microfit 0430200608 1 Microfit 0430250600 1 -
Version 2022.02.05
557 downloads
Top Corner Cable Hide/Cover (LED Wires) Designed to hide cables that are running around the top corners of 2.4 extrusions behind the z idlers. They are large enough to fit 3 pin microfit connectors. There maybe some small loss in z. Don't forget to check your clearances after installing. Pro tip: It may take some fiddling to get the wires to fit. You will know they are in place when it sits flush to the extrusions without wobbling. Also disable 'Thin Walls/Detect Thin walls' so the mounting ears print cleanly. Printing Default voron settings No supports needed BOM Size Qty M3x8 8 M3 T-Nut 8
