Voron 2 - Questions

111 questions in this forum

1. My new PLA filament keep clogging after print

   Asked by Pradit, January 18, 2023

   0 votes
   7 answers
2. Klipperscreen not working

   Asked by nannyogg82, January 8, 2023

   0 votes
   1 answer
3. What cause purge_bucket macro to retract instead of purge?

   Asked by Pradit, January 4, 2023

   0 votes
   3 answers
4. Just couldn't QGL anymore... Too many tries.

   Asked by Pradit, December 23, 2022

   • qgl
   • v2.4
   0 votes
   13 answers
5. Klipper doesn't auto write the config after Save_config...

   Asked by Pradit, December 24, 2022

   • linux
   • klipper
   • config
   • octoprint
   0 votes
   12 answers
6. Unable to obtain 'adxl345_status' response, and many other errors...

   Asked by Pradit, December 24, 2022

   0 votes
   0 answers
7. Stealthburner neopixel part LED not ON

   Asked by Pradit, December 15, 2022

   • led
   • klipper
   • stealthburner
   1 vote
   6 answers
8. What type of connector do you use with probe and ebb36?

   Asked by Pradit, December 17, 2022

   0 votes
   0 answers
9. Where should I begin looking for the cause/solution for this error message?

   Asked by QuailMan, December 16, 2022

   • klipper
   • config
   0 votes
   3 answers
10. Voron 2.4 gantry dragging on X axis

    Asked by Pradit, December 15, 2022

    • v2.4
    • belt
    0 votes
    1 answer
11. Problem with Stealthburner PCB

    Asked by Stadi, November 13, 2022

    • stealthburner
    • klicky
    • pcb
    0 votes
    8 answers
12. Help with Print_Start macro and SuperSlicer

    Asked by Penatr8tor, November 28, 2022

    0 votes
    17 answers
13. Voron 2.4 print start location

    Asked by nannyogg82, October 29, 2022

    • print start
    0 votes
    127 answers
14. Euclid probe update Voron 2.4 v1- Error message " File contains no section headers???"

    Asked by SteveS, November 6, 2022

    • euclid
    • v2.4
    • probe
    0 votes
    7 answers
15. Xyz Steps.

    Asked by Vargsh0rd3, October 23, 2022

    0 votes
    2 answers
16. Fly XY 1 endstop not opening

    Asked by evan.bas, October 13, 2022

    0 votes
    5 answers
17. Bigtreetech U2C & EBB42 Canbus board firmware

    Asked by Emanuel, October 11, 2022

    • btt
    • canbus
    0 votes
    1 answer
18. gcode_macro PRINT_START

    Asked by ValèreTARBY, October 1, 2022

    • klipper
    • macro
    0 votes
    3 answers
19. Build plate wiring.

    Asked by dgrosen, September 25, 2022

    0 votes
    2 answers
20. the question about x and y axes

    Asked by ado1111, September 18, 2022

    0 votes
    7 answers
21. Euclid Probe

    Asked by Dale, August 20, 2022

    0 votes
    5 answers
22. Din Mounts

    Asked by mcham, August 31, 2022

    0 votes
    3 answers
23. Led Strip Lighting Wiring to Octopus

    Asked by Wannabe, August 18, 2022

    0 votes
    2 answers
24. Hotend/duct not moving smoothly X axis (left to right)

    Asked by Buurman, August 1, 2022

    0 votes
    39 answers
25. Klicky Probe bed_mesh_calibrate in Start cgode

    Asked by hopeinformer, July 9, 2022

    0 votes
    30 answers